4 Series Features Using the latest digital signal processing and high sample rates would be wasted if attention is not paid to capturing the signal as faithfully as possible, and reproducing it accurately. The range uses high-performance 24-bit converters on the inputs and outputs, running at 96kHz to give a bandwidth of over 30kHz and a dynamic range in excess of 116dB. With two or four fully balanced inputs, and up to eight fully balanced outputs, it also offers greatly increased flexibility. Now it's possible to realise (for example) four two-way monitor systems, or your favourite DP226 configuration with an additional stereo processing channel, all in a single 1U unit. With multiple inputs and outputs, the 4 Series are able to offer much more than a simple crossover system. To make configuration as simple as possible, a selection of templates are available to set the system up, taking care of routing and selecting useful crossover points. |
However all of this is easily adjustable,
including the routing. Any output may be fed from any input, or combination of
inputs, forming a completely flexible matrix. The 4 Series processing platform has been designed to operate at a native sampling rate of 96kHz, and also be powerful enough to cope with the additional inputs and outputs. Available on each input channel is a 28 band graphic equaliser, in addition to 8 bands of fully parametric equalisation. Each output path features up to 9 parametric sections, in addition to the crossover filters which themselves now offer slopes from 6dB/Octave up to 48dB/Octave. |
All parametric sections can be reconfigured to many alternate
filter behaviours, including the familiar high and low shelves and notch
filters, but along with bandpass, elliptic and variable 'Q' shapes, and phase
adjustment, in 2 degree steps. Each output also features a combination of
limiters - a limiter which is designed to protect individual drivers from
over-excursion/over-driving, and an additional look-ahead "D-Max" limiter for
added safety. Add to this sub-millimetre accuracy when introducing time alignment with completely flexible ganging of all channels, and it can be seen that a member of the 4 Series will fit the bill in any system configuration. |
4 Series Specifications Inputs Electronically balanced (transformers optional) AES/EBU (selectable) fitted as standard to all Series 4 units Impedance >10k ohms CMRR >65dB 50Hz - 10kHz Outputs All electronically balanced (transformers optional) AES/EBU fitted as standard to all Series 4 units Source Imp < 60ohms Minimum Load 600ohm Maximum Level +20dBm into 600 ohm load Sampling Rate DP428 – Up to 96kHz internal, up to 192kHz can be accepted and converted. |
Frequency Response ±0.5dB 10Hz - 32kHz Dynamic Range >116dB 20Hz -20kHz. Unwtd Distortion < 0.001% @ 1kHz, +10dBm Maximum Delay 650 mS. (increment 0.325 µs steps) Output gain Adjustable +15dB to -40dB in 0.1 dB steps and mute Equalisation Filters Parametrics - 8 Per input / 9 per output Additional filters 28-band graphic on each input Each parametric can be switched to Bandpass, Allpass, Notch, VariQ, Shelf and Elliptical response Phase filtering - 2 degree steps on each input and output Crossover Filters Bessel / Butterworth 6/12/18/24/48dB per octave and Linkwitz-Riley 12/24/48dB per octave |
Limiter Threshold +22dBu to -10dBu Attack time 0.3 to 90 milliseconds Release time 4, 8, 16 or 32 times the attack time Clip/D-max Limiter Look-ahead attack time, Fast, Medium or Slow release times Connectors Inputs 3 pin female XLR Outputs 3 pin male XLR RS485 In/Out XLRs RS232 9 Pin (Female) D Connector Power 3 pin IEC Power 60VAC - 240VAC Consumption < 40 watts Weight 3.5kg. Net (5kg. Shipping) Size 1.75”(1U) x 19” x 12” (44 x 482 x 305mm) excluding connectors Due to continuing product improvement the above specifications are subject to change. |
최근 프로 페셔널 오디오 시스템에 강하게 요구되는 기대에 걸맞는 향상된 품질과 편리성을 가진 제품이다. 사용의 편리성을 중점에 두었으며,
새로운 오디오 프로세싱 플랫폼을 기반으로 원음 그대로의 음질인 96khz의 샘플율을 사용하여 4 series는 새로운 오디오 퍼포먼스의 표준을
제시하였다.
DP226의 성공으로 세계적인 Loudspeaker management산업의 표준으로 명성을 떨친 XTA는 XTA
제품을 한번도 사용해 보지 못한 고객도 쉽게 사용할 수 있게 설계되었다.
입력& 출력
24비트의 높은 대역폭의
컨버터가 입력과 출력에 장비되어 있기 때문에 96khz로 작동하면서 30khz와 116db를 뛰어넘는 성능을 가지고 있습니다.
2개나 4개의 밸런스 입력과 8개에 밸런스 출력은 매우 다양한 방법으로 조작할 수 있다. 4개의 two-way 모니터 시스템들을
인식할 수 있다. 또는, 1U 유닛에 스테레오 프로세싱 채널을 추가하여 DP226을 장착할 수 있다
크로스오버 파워
4
시리즈는 처음의 96kHz의 샘플링율에서 가동되게끔 설계되었다. 또한, 추가된 입력과 출력을 처리하기에 충분한 파워를 가지고 있다. 각각의
입력채널에서 28밴드 그래픽 EQ가 되며, 추가로 8밴드의 파라미터 EQ가 가능하다. 각각의 출력 패스는 최대 9개의 파리미터 섹선이 가능하며,
자체적으로 6dB/옥타브에서 최대 48dB/옥타브까지 가능한 크로스오버 필터를 추가할 수 있다.
입력 매트릭스
다중의 입력과
출력을 지닌 4 시리즈는 간단한 크로스오버 시스템보다 훨씬 더 많은 특징들을 가지고 있다. 조작하는데 있어 배열을 간단하게 하기 위해서, 시스템
설정, 루팅과 유용한 크로스오버 포인트 선택 등의 템플렛 섹션이 가능하다.
디지털 입력/출력
디지털 영역에서 라이브 사운드의
분배가 증가함에 따라, 시스템은 아날로그와 디지털 피드 사이 또한, 입력과 출력용 모두에서 선이 보이지 않는 스위치가 가능하도록 요구되고
있다.
기기가 디지털 입력 모두와 피드 디지털 출력 스트림이 작동할 수 있게 하는 AES/EBU 인터페이스는 내장되어 있다.
32kHz에서 최대 192kHz까지 스트림을 받을 수 있는 샘플율 컨버터는 입력에 포함되어 있다.
원격조정
모든 시스템
유닛(DP226, DP224, DP6i 포함)은 노트북이나 터치스크린 테블렛 PC 등을 통해 무선 컨트롤과 모니터가 가능하다.
일반
PC (또는 컨버터를 통한 USB 포트)에서 시리얼 포트로 연결하기 위한 지원은 간단히 XLR 케이블을 통해 유닛의 장거리 네트워크용인RS485
포트가 포함된다.
입력 밸런스
임피던스: >10k Ohms
CMRR: >65dB 50Hz ~
10kHz
출력 밸런스
소스 임피던스: <60 Ohms
최소 로드: 600
Ohms
최대 레벨: +20dB ~ 600 Ohms 로드
샘플링율: 최대 96kHz 내부, 최대 192kHz까지 받을 수 있으며 변환
가능
주파수응답: ±0.5dB 10Hz - 32kHz
대역폭: >114dB 20Hz ~ 20kHz
왜곡:
<0.001% @ 1kHz, ±10dBm
최대 딜레이: 650mS
출력 게인 조정: 0.1dB 스텝 & 뮤트에서
+15dB ~ -40dB
EQ
필터 패라메트릭스: 입력 당 8개 / 출력 당
9개
추가 필터: 각 입력에 28밴드 그래픽
위상 필터링: 각각의 입력 및 출력에서 -2도 스텝
크로스오버
필터
Bessel/Butterworth: 옥타브 당 6/12/18/24/48dB
Linkwitz-Riley:
옥타브 당 12/24/48dB
리미터
Threshold: +22dB ~
-10dB
어택 타임: 0.3 ~ 90ms
릴리즈 타임: 어택 타임의 4, 8, 16 혹은
32배
커넥터
입력: 3 핀 female XLR
출력: 3 핑 male
XLR
RS485 입/출력 XLR
RS232 9핀 D 커넥터
크기: 44 x 482 x 305mm
무게:
3.5kg
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
상품이 장바구니에 담겼습니다.
바로 확인하시겠습니까?
상품이 찜 리스트에 담겼습니다.
바로 확인하시겠습니까?